
Using Recommendations
- Minimum bucket spacing: bucket depth “C” +2mm.
- For engineering purposes, we recommend using“L” for usable capacity.
- Mounting holes can be customized on request.
Model | Bucket Dimension (mm) | Mounting Holes (mm) | Capacity (L) | ||||||
---|---|---|---|---|---|---|---|---|---|
Length A | Proj. B | Depth C | From Top D | Hole Centres E | No. of Holes | Hole Diameter | Water Level (Z-Y) | Total Level(X-Y) | |
DM1010 | 105 | 110 | 129 | 48 | 50 | 2 | 9 | 0.53 | 0.7 |
DM1310 | 138 | 110 | 128 | 37 | 80 | 2 | 7 | 0.62 | 0.88 |
DM1413 | 143 | 143 | 172 | 52 | 93 | 2 | 9 | 0.93 | 1.6 |
DM2313 | 230 | 138 | 126 | 44 | 125 | 2 | 7 | 1.54 | 2.21 |
DM1715 | 175 | 156 | 176 | 52 | 113 | 2 | 9 | 1.6 | 2.4 |
DM2517 | 258 | 172 | 183 | 52 | 93 | 3 | 9 | 3.4 | 4.1 |
DM2917 | 296 | 173 | 197 | 61 | 110 | 3 | 9 | 4 | 5.26 |
DM2419 | 240 | 190 | 200 | 65 | 90 | 3 | 9 | 3.52 | 4.73 |
▲DM2919 | 290 | 199 | 200 | 53 | 92 | 3 | 9 | 2.8 | 5.3 |
DM2921 | 294 | 210 | 200 | 55 | 113 | 3 | 9 | 4.33 | 6 |
DM2118 | 215 | 178 | 195 | 65 | 120 | 2 | 9 | 2.5 | 3.78 |
DM2918 | 292 | 178 | 195 | 65 | 100 | 3 | 9 | 3.44 | 5.25 |
DM3321 | 337 | 215 | 215 | 66 | 85 | 4 | 9 | 5.38 | 8.16 |
DM3921 | 395 | 215 | 215 | 66 | 100 | 4 | 9 | 6.1 | 9.25 |
DM4721 | 480 | 215 | 215 | 66 | 95 | 5 | 9 | 7.51 | 11.38 |
▲DM4721G | 480 | 215 | 215 | 66 | 95 | 5 | 9 | 7.51 | 11.38 |
Note: “▲” marked size buckets come with higher mounting holes and side wall.
*Actual dimensions of the buckets will vary slightly depending on specified raw material. The dimensions shown above are for HDPE buckets. Size A, B and C for Nylon and Urethane buckets will be about dimensionally 2% larger than HDPE buckets.
Elevator Buckets
- Over 12 different elevator bucket styles are available for agricultural and industrial applications.
- A direct replacement for many other international brands.
- Unique elevator bucket design with multiple patents.
- Our elevator buckets are well regarded, worldwide for high price/quality ratio.

ELEVATOR BUCKET MATERIAL OPTIONS
Material | Mild Steel | Stainless | HDPE | Nylon 6 | Reinforced Nylon | PU |
Cost | ![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Wear Resistance | ![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Impact Resistance | ![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
FDA Food Approved | ![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Max Temp℃ Continuous | 180+ | 250+ | 70 | 100 | 110 | 70 |
Max Temp℃ Peak | 220 | 400 | 80 | 120 | 130 | 80 |
HDPE: Tough and flexible, suitable for handling grains, foodstuffs, and other products with no sharp edges and material that has a bulk density of less than 1g/cm³ .
Nylon: High impact and abrasion resistance, better heat resistance and are well suited for handling hot, abrasive and sticky products.
PU: Extremely abrasion resistance, tough and flexible, and are suitable for handling sharp, cutting and sticky products.
Mild Steel: General purpose, long life, well suited to agricultural and industrial products.
Stainless Steel: Food grade, corrosive resistance, suitable for food and high-temperature applications.
MEASURE AN ELEVATOR BUCKET
ELEVATOR BUCKET VENTING
A venting bucket can improve the eficiency of some bucket elevators when handling certain products. On dense materials such as lour, meals, and mash feeds, the vents allow air to escape through the cup as it fills, which permits the cup to fill more completely. During discharge, air can return through the cups as it empties, thus preventing a vacuum that could hold some of the products in the cup and cause backlegging.
On extremely light materials such as alfalfa meal, screenings and bran, a vented bucket not only minimizes blowing of the product during loading and discharge, but also reduces air turbulence in the leg as the bucket travels empty down the return side of the elevator. A reduction in air currents minimizes the vacuum which can draw a light product through the down leg and back to the boot.
We have four standard patterns available which offer varying amounts of air release for the handling of most products. Custom venting is available upon request.
Venting Options

Vent Pattern 1
One row of 6mm or 8mm
holes in body with same hole
center and number of holes as
mounting holes in back.

Vent Pattern 2
One row of 6mm or 8mm holes
in body on 25mm centers.

Vent Pattern 3
Two rows of 6mm or 8mm holes
in body on 25mm centers.

Vent Pattern 4
Two rows of 6mm or 8mm holes
in body on 25mm centers, three
holes of 6mm or 8mm on each
side.

Custom Vent
Vented as required.


There are no reviews yet.